Recently the garage door opener stopped and shows continuous blue light on it.
how do i reset it?
It is worked! my mistake
I didn't : Don't forget to cross Tx/Rx
you helped me revive 2 of these devices.
A common oversight😉
great, that it worked out!
I bought the same usb UART converter. I have the original firmware from Atom. I'm trying your setup for each of your steps but still getting the error. I tried various esp flashers.
Permission error 13
I tried on WINDOWD 10 and WINDOW11, 3 workstations.
The same result :(
COM port is blocked, already used.
Or connection to the unit is not correct. Please share a picture of your wireing.
Now my new athom garage door opener HomeKit stuck on ESP-D8FE41.
I can connect to this wifi ESP-D8FE41 but I can't configure the device because 192.168.4.1 is not responding!
I bought new athom device today!
In description it says "no hub required".
But now it Works only in the same wifi.
What is going on
But it's not connecting to apple home!!!
Does anyone have backup firmware of athom garage door opener homekit?
Hello, yesterday I have installed the newest firmware 0.85(OTA) my on my garage door opener(homekit version).
After that the opener isn't working.
It’s connected to the wifi and I can see and check it in the browser.
In homekit the device is displayed and I can switch it, but the output is not switched.
I made a reset and reinstall but isn't working.
My second one is working fine. (with 0.85)
Where can I download the update file?
Update: I have found the failure.
After the OTA upgrade the relay time was changed to 0.0 s.
With time 1.0 s my device is working again.
Just got my 1st unit "working" again.
In lack of the original athom FW file - Anyone knows, where this can be downloaded?
I just uploaded latest TASMOTA 13.0.0(tasmota) and the device is booting up again!
Maybe I will even spend some time on this and configure Tasmota to run the relay and read the magnet switch...
Or flash back the original FW, if it is available somewhere.
Bridge GND and Boot
And connect 3V, GND, Rx, Tx to UART converter
(5V will kill the ESP32 chip, do not use that, as many UART connectors have both)
Do not forget to cross Tx/Rx
I used latest Tasmota image and ESP Flasher
BTW, opening up the black ATHOM housing is a bit tricky. It is NOT made to be opened again, hence one needs to break the internal clamps to get it open.
Thanks for your quick response.
I can configure, but is not connecting to any app. What app should I try. I tried Tuya and Homekit
Well, you now have the HomeKit FW on, so you should connect it with HomeKit...
Did you join the device to your local WLAN?
Is firmware you linked for homekit because homekit now is not finding device.
Is there any other firmware specialy for homekit version?
My athom homekit doesn't show wifi at all so i can configure it. It stuck on blue light. Is there any way how to reset it
Continious blue light since two weeks. Device does not turn up on WiFi anymore.
I ordered a new one...
Most likely FW got corrupted. If I find time I might try to flash it again.
I ordered a new one and after 2 months its faulty like previous one. Continues blue light. How to flash it?
Check my new post. Seems, that they are not really dead, just currupted FW.
Still need to get my hands on the ATHOM FW file.
Can anyone please provide the setup code for apple homekit? I think if i had this i could add the door opener back on.
Setup code is : 826-68-266
because it does not go back to the previous version, which can be managed with the TUYA app, it worked very well.
bad service Athom delivers, does not respond and does not give solutions.
my firmware is 8,4 however i can reconnect to apple homekit. i have emailed many times to Anthom asking for the connection code hoever they wont respond : (
The same thing happened to me, this happened to me when I changed the Wi -Fi network in the team, and I have not been able to reset.
Do you know the firmware version number of the current controller?
Mine was 0.8.5.