• Home

  • Products

    • Local Shipping
    • Tasmota
    • ESPHome
    • WLED
    • Homekit
    • Home Bridge
  • Forum

  • About Shipping

  • Contact Us

  • 更多

    Use tab to navigate through the menu items.
    0
    Para ver esto en acción, dirígete a tu sitio ya publicado.
    • Categorías
    • Todas las entradas
    • Mis entradas

    ATHOM Open Hardware Forum

    TASMOTA/ESPHome/HAA/Home Assistant/OpenHAB/ESP8266

    General Discussions

    Share stories, ideas, pictures and more!
    Vistas 
    Entradas13

    Tasmota Related

    for Tasmota
    Vistas 
    Entradas15

    ESPHome Related

    ESPHome related
    Vistas 
    Entradas10

    Homekit related

    Gas/Motion/Door Window/Siren/Thermostat etc
    Vistas 
    Entradas21

    WLED Related

    Welcome! Have a look around and join the conversations.
    Vistas 
    Entradas16

    Home Assitant

    Locks/Camera/Door bell etc
    Vistas 
    Entradas2

    Light

    Lighting Bulb/Strip/Indoor Fixturers/Controllers
    Vistas 
    Entradas27

    Plugs

    Indoor/outdoor plugs
    Vistas 
    Entradas24

    Wall Switch

    No neutral needed/Neutral needed/ Touch Pannel/Dimmar
    Vistas 
    Entradas39

    Relay Switch

    220V/5V/12V relay switch etc
    Vistas 
    Entradas6

    Others

    Information about intergrate with other App
    Vistas 
    Entradas1
    Nuevas entradas
    • chyldofthebeat
      5h
      WLED 0.13.3_ESP01.bin flashed to Athom LS-4P, can't find it at all on my network
      WLED Related
      Hello! I used the web interface in WLED for the Athom LS-4P to flash it to WLED 0.13.3 using apparently the WLED 0.13.3_ESP01.bin file. I thought I had download the ESP02.bin file, but it must've been the wrong one. It said it flashed successfully. However, now my controller won't currently boot up. Is there any way possible that I could connect this controller to my computer so that I may use esptool to fix it? Alternatively, is there any other way to fix it?
      2 comentarios2
      0
    • tom jones
      22 sept
      Athom 8 Channel Relay Firmware
      Homekit related
      Is there a firmware update for this relay device. It seems to have terrible range problems. Any other tips for increasing signal strength? What is the current firmware for this device?
      0 comentarios0
      0
    • starfel1982
      17 sept
      Is my LED controller bricked?
      WLED Related
      I just received my LED controller (the smaller, 2amp version) - after hooking it up to a 5v power supply by itself (no led strip), I connected to the AP, setup the network configuration. So far so good, after this I added it in the WLED app, as well as connected it through my browser, again, so far so good. At this point i disconnected the power and left the house for a bit. After coming back home, I reconnected the power supply to the controller, and nothing works. I cannot connect through it from the app, nor is it even connected to the wifi anymore (i checked this by doing a PING to the ip as well as checking the connected clients from my router setup. It's simply not there. I tried multiple ways of resetting the device, holding the button 7 seconds according to the manual. 10 seconds according to the forum, it just doesn't work. Am i doing the reset the wrong way? Is there another procedure to get this device to return to factory settings? Is my LED controller bricked? I am finding no luck whatsoever to get this thing to reset. Kindly help! Many thanks in advance.
      0 comentarios0
      0

    ©2020 by athom.