• Home

  • Products

    • Local Shipping
    • Tasmota
    • ESPHome
    • WLED
    • Homekit
    • Home Bridge
  • Forum

  • About Shipping

  • Contact Us

  • 更多

    Use tab to navigate through the menu items.
    0
    Para ver esto en acción, dirígete a tu sitio ya publicado.
    • Categorías
    • Todas las entradas
    • Mis entradas
    eslam fikry
    07 abr 2021

    Smart switch restarting by itself

    en Wall Switch

    I have issue with Athom smart switch 2 gang it's restarting by itself after 1 or 2 min and turn off the light

    and no response in apple homekit


    11 comentarios
    0
    11 comentarios

    Comparte lo que piensasRegístrate para dejar un comentario.

    G
    Goran Skular
    Goran Skular
    21 ene

    UPDATE: my problem with restarting is solved. More info here https://www.athom.tech/forum/esphome-related-1/esphome-switches-restarting-led1-gpio14-problem


    I do have a Problem 2 with led1 still on ESPHome...

    Me gusta

    G
    Goran Skular
    Goran Skular
    21 ene

    I tried with a new ESPHome firmware, couple devices... and eventually also with Tasmota firmware. In a 'no neutral' configuration it just restarts when relay is turned on. Disclaimer: maybe it works 'with neutral' configuration, but I can't use it that way.


    It can be that it's a hardware related problem.


    More in detail on ESPHome forum: https://www.athom.tech/forum/esphome-related-1/esphome-switches-restarting-led1-gpio14-problem


    Ahhh.. and what to do now?


    Me gusta

    G
    Goran Skular
    Goran Skular
    21 ene

    I just bought 48 wall switches, EURO version.. and have the same problem. I updated esphome to 2022.1.1 and still the device restarts all the time. I use no-neutral connection.

    Me gusta

    gonzalo_dd
    06 jun 2021

    can someone from the company contact me? My email es gonzalo_dd (at) hotmail (dot) com

    Me gusta

    gonzalo_dd
    02 jun 2021

    I see… is it too complex to update via serial port?

    Me gusta
    Athom_Support
    02 jun 2021
    Contestando a

    Need welding

    Me gusta

    G
    G D
    G D
    12 ago
    Contestando a

    No problem welding. I understand that if something goes wrong it will be my fault, but anyways in the current state with firmware version 0.2 the switch is unusable and non-upgradable. Can you share some instructions about the actual procedure?

    Me gusta

    Athom_Support
    02 jun 2021

    0.2 may not be able to upgrade, the version must be greater than or equal to 0.3 to upgrade, and the version below 0.2 must be burned through the serial port!

    Me gusta

    gonzalo_dd
    02 jun 2021

    model says SW034US, version 0.2. What address should I send email?

    Me gusta

    Athom_Support
    02 jun 2021

    Take a look at the version number of the switch firmware, the latest version is 0.6, if you need to upgrade, you can contact us by email

    Me gusta

    gonzalo_dd
    02 jun 2021

    I have the same issue. Any solutions?

    Me gusta
    11 comentarios
    Entradas similares
    • Color led switch
    • Tasmota dimmer switch?
    • ESPHome Switches restarting + LED1 (gpio14) problem - restarting SOLVED

    ©2020 by athom.